|
|
6 parts manufactured and pre-assembled. Cast component (GD-Al9Cu3) manufactured from a 1 cav. tool. Cover (ABS/PC) manufactured from a 1 cav. tool Manufactured, sealing ring (not visible), from a 1 cav. tool Per 2 screws and plates after customer subscription Tools and components manufacture in R.of China |
 |
|
|
|
Magnesium steering wheel (GD-MgAlMn.) weight approx. 850 grams 6 x 1- fold tools Tool manufacturing in China Components manufacture in Spain |
 |
Tool for door interior trim Tool: In front of tempered steel (NAK 80, HRc 38 ... 42) Construction time period up to pilot series parts 12 weeks Hot runner Tool measurement: 1600x1400 mm Manufacturing place tools: Taipei (P.R. of China.) Share manufactured from PP not reinforced Components manufacture: P.R. of China |
|
|
Injection moulding toolkit for motor vehicle (Caravan.) Uses of tools: Hardened 1.2379 and 1.2344 ( HRc 48-52) Construction time period up to pilot series parts 4 weeks One 1+1fold and one 1-fold tool with slides - actions vigour cast having been engaged hydraulically Tool measurements different Manufacturing place tools: Shenzen (P.R. of China.) Share 15% GF manufactured from PBT+; Components manufacture Shenzen |
|
|
|
|
|
Injection mould tool for "bumper cover in front for Nissan" Tool was manufactured for the spare part market. Uses of tools: In front of tempered steel (NAK 80, HRc 38 ... 42) Cores and slide from PDS 5 Construction time period up to the series 18 weeks tool weight approx. 18.600 kg, Outer form partly polished in the lower area structures, became structure after presentation prepared, inside contour with structure in accordance with VDI3400 REF. 18 ... 33. Manufacturing place: Kaoshiung (R. of China.) |
|
|
Toolkit for AUDI AVANT vehicles, existing from tool key framework with 2 slides and seal slide with one Slide. The parts (tools) were coordinated so that a stick neither a vibrating in use can appear still at all temperatures to be expected! Tools were manufactured for the series need. Uses of tools hardened HRc 42 .. 48 from 1.2311 Cores and slides hardened HRc 54 .. from 1.2767. 58 Construction time period up to the pilot series 8 weeks Wider areas with structure polish view areas, appropriate VDI3400 REF. 21st parts are painted .. Manufacturing place: Tainan Hsien (R. of China.) |
|
|
Injection moulding tool for "edge of baggae area" for BMW 850", cable runs splashed into the boot as a termination segment built-inly Uses of tools: In front of tempered steel (NAK 80, HRc 38 ... 42) Construction time period up to pilot series parts 14 weeks Tool measurements approx. 1900 x 796 x 996 mm, weight 8.800 kg, Cycle time for parts from ABS/PC fade in 50 seconds on Klöckner Windsor FAP W1000 LW. The side not visible in the picture was structured after presentation Standex BMW1 Manufacturing place: Taipei (R. of China.) |
|
|
Injection moulding tools for "Air guiding parts for VW - AUDI " Become parts in the not visible area of the engine compartment and this one Sub-ground group installed. (Air conveyance for brake system.) Uses of tools: In front of tempered steel (NAK 80, HRc 38 ... 42) Construction time period up to pilot series parts 14 weeks Self dividing ever 2 foldly tool off with up to 8 slides, Film runner gate Tool measurements approx. 896 x796 x 696 mm, weight approx. 4.200 kg, Parts manufactured from PP/EPDM Manufacturing place: Taipei (R. of China.) |
|
|
|
|
|
Injection moulding tool for "loudspeaker covers" Uses of tools: In front of tempered steel (NAK 80, HRc 38 ... 42) All cores and slide hardened, HRc 48 ... 52 Construction time period up to pilot series parts 18 weeks 2-fold tool with six slides, hot runner subgate Tool measurements approx. 596 x796 x 596 mm, weight approx. 1.700 kg, Manufacturing place: Taipei city centre (R. of China.) Parts manufactured from PP, components manufacture in Turkey and in France |
|
|
Injection moulding toolkit for "window lifter (crank)" Uses of tools: In front of tempered steel (NAK 80, HRc 38 ... 42) Construction time period up to pilot series parts 12 weeks Respective 4-fold tools with slides, hot runner gate Tool measurements different And EPDM, components manufacture, share manufactured dazzle from ABS/PC in Turkey. Manufacturing place tools: Taipei (R. of China.) |
|
|
Brake shoe for light and middle heavy trucks Manufacturing of the part is carried out after customer subscriptions. Material: Steel in accordance with customer requirement Material thickness: 8 to 13 mm Measurements: Approx. 240x180x220 mm Manufacturing of the tools: Turkey Manufacturing place parts: Turkey Supplier countries: E.U and Turkey |
 |
Wheel decorating cap for Honda Civic. Part is - dazzle and manufactured in grey synthetic material then fully automatically lacquered 1-cav. tool with a central hot runner gate Manufacturing place tools: Turkey (Izmir.) Manufacturing place parts: Turkey (Bursa.) |
